CD5002/CN5002: Analysis and Design of a Computer Network using Cisco Packet Tracer - IT/Computer Science Assignment Help

Assignment Task:

Task:

Aim
Computation and allocation of IP addresses to devices in a computer network (based on a given block address), followed by design and simulation of the network using Cisco Packet Tracer software.
1. Deadlines

• Friday 14th May 2021: Submissions of Packet Tracer file and report via Moodle

2. Coursework Requirement
Each student must use their student’s number and the algorithm given below to determine their block IP address. Then each student must allocate an IP address to devices in the given scenario and configure the network using Cisco Packet Tracer software. This must be followed by simulation of the designed network and usage of debugging techniques (i.e. PDU or Ping command) to ensure satisfactory operation of all devices on the network.

2.1 Algorithm to Determine Each Student’s Block IP Address
Each student’s number uxxxxxxx must be converted into the format xxx.xx.xx.0/25 by applying the following procedure to obtain the student’s block IP address and mask for the coursework:

Use your student’s number to create your individual block IP address as follows:

First section of IP
1. If first digit is 1or 2 then take the first three digits as the first section of IP address.
2. If first digit is 0, then take the first three digit and replace the leading 0 by 1, for the first section of IP address.
Second section of IP
1. Take the next 2 digits (digit 4th and 5th of your student number) for the second section the IP address;
2. If both are 0s (zeros) replace them by 11 and if only the digit 4th is 0 then ignore it (i.e. do not include it in your IP address).

Third section of IP
1. For the third section of the IP address, take the following 2 digits (digit 6th and 7th);
2. If both are 0s (zeros) replace them by 11 and if only the 6th digit is 0 then ignore it (i.e. do not include it in the IP address).
Fourth section of IP
1. The last section of the IP address must be zero Mask
2. Finally, the mask is /25.

Activities to be carried out in the Coursework
Use the Cisco Packet Tracer and the information below to analyse and create
a small network. This requires connecting the network devices given below
and configuring the active nodes (i.e. host computers, routers etc.) to form
network connectivity.

The given devices are listed below with the subnet details in Table 1:

• Cisco Routers
• Cisco Switches
• Computers (hosts), see Table 1
• Servers
• Connecting cables, see Table 3
Table 1

Subnets Number of Hosts
Subnet A No computer
Subnet B No computer
Subnet C No computer
Subnet D 1 server and 4 computers
Subnet E 1 server and 18 computers
Subnet F 1 server and 20 computers

Task 3.1 Analysis and Design of the Logical Network

Compute and determine the Network Address, Address Mask, Sub- netting and other addresses in Table 2 using the lecture material and information from the recommended textbook as a guide.
Task: 3.1.1: - Using the classless IP address computation techniques and block IP address and mask xxx.xx.xx.0/25 (address / mask) you obtained from Task 2.1.0 perform the following tasks:
• Determine the number of addresses in the network
• Last Host Address, the Broadcast and the Bit mask etc.
• Complete Table 2 below for each subnet class A, B, C, D, E, and F.

Conduct the above calculation for your IP addresses and design an IP address scheme that satisfies the requirements in Table 1 above.

• Show the step by step procedure you used to complete Table 2 below.
• Hints: - for the classless computation use either the binary or AND/OR approach or any other method in the recommended textbook/lectures.
• Students are required to show and explain steps used for IP calculation.
• For the sub-netting computation use the technique in the recommended textbook or any acceptable method but explain the procedure used.

This CD5002 IT Assignment has been solved by our IT Experts at My Uni Paper. Our Assignment Writing Experts are efficient to provide a fresh solution to this question. We are serving more than 10000+Students in Australia, UK & US by helping them to score HD in their academics. Our Experts are well trained to follow all marking rubrics & referencing style.

Be it a used or new solution, the quality of the work submitted by our assignment Experts remains unhampered. You may continue to expect the same or even better quality with the used and new assignment solution files respectively. There’s one thing to be noticed that you could choose one between the two and acquire an HD either way. You could choose a new assignment solution file to get yourself an exclusive, plagiarism (with free Turnitin file), expert quality assignment or order an old solution file that was considered worthy of the highest distinction.