CPCCBC4018A - Two Pegs on Plan View - Engineering Assignment Help

Assignment Task

Questions
1. You have taken a measurement on Lot 14 from the south west corner to the north east corner of the allotment. The measurement you obtained from your tape measure, laying it on the ground, was 43,866 mm, measured to the nearest millimetre.
Is this the true dimension for the distance between the two pegs on plan view?
If the answer to part ‘a’ is no, what is the true dimension on plan view and explain the reason for the difference? (use Pythagoras’ theorem)

2. You have engaged a surveyor to carry out an identification survey of Lot 14 (peg the four corners of the boundaries) and to peg the 6m building line (the setback of the house from the front boundary).
From the north west corner of the allotment, calculate the angle and distance to the north west corner of the proposed building
From the contours determine the total fall across the footprint of the building
Assuming you will construct a level, rectangular platform for the construction of the building, extending 1m beyond the external walls of the building, what are the approximate dimensions of this platform?
Utilizing the surveyors pegs, outline, step by step, how you would set out the building using profiles and string lines to allow any excavation, formwork/slab construction to be accurately completed.
Outline how you would construct the formwork to achieve the required Finished Floor Level.
From finished floor level shown on the drawings (RL 0.000), subtract 200mm to allow for the slab and sub grade thickness. This reduced level is sometimes referred to as the bulk excavation level (BEL). From this BEL, the contours, and the dimensions of the rectangular platform, calculate the approximate volume of the bulk excavation for the building (use diagrams where needed to illustrate your method).

3. Assuming the RL at the top of the vehicle access (crossing) is 0.030, the top of kerb is -0.030 and the kerb height is 100mm,
Draw a longitudinal section of the vehicle crossing from the kerb to the front boundary Lot 14. (Note that the length of the crossing is 3.2m; determined by scaling off the drawing)
Determine the grade from the top of the crossing to the bottom of kerb as a percentage and a ratio.

4. The client on Project 1 has requested provision be made for storm water detention on the site. The hydraulics engineer has calculated the capacity of the pit necessary for the site to be 23,000 litres.
Calculate a pit dimension that would meet this capacity requirement and that can be constructed within the front area of the property; that is, in the area between the front boundary and the front building line. Do not position the tank within 3m of the building. (1000L = 1m3)
right

NOTE: This is a competency-based assessment. You will receive a result of Satisfactory or Unsatisfactory. This means that you must satisfactorily complete each question (or part thereof) to meet the competency requirements set out in the training package. If you do not meet the competency requirements, you will need to resubmit your assessment until competency is achieved.

NOTE: This is a competency-based assessment. You will receive a result of Satisfactory or Unsatisfactory. This means that you must satisfactorily complete each question (or part thereof) to meet the competency requirements set out in the training package. If you do not meet the competency requirements, you will need to resubmit your assessment until competency is achieved.

This CPCCBC4018A - Engineering Assignment has been solved by our Engineering experts at My Uni Paper. Our Assignment Writing Experts are efficient to provide a fresh solution to this question. We are serving more than 10000+ Students in Australia, UK & US by helping them to score HD in their academics. Our Experts are well trained to follow all marking rubrics & referencing style.
Be it a used or new solution, the quality of the work submitted by our assignment experts remains unhampered. You may continue to expect the same or even better quality with the used and new assignment solution files respectively. There’s one thing to be noticed that you could choose one between the two and acquire an HD either way. You could choose a new assignment solution file to get yourself an exclusive, plagiarism (with free Turnitin file), expert quality assignment or order an old solution file that was considered worthy of the highest distinction.